In our company innovation is the starting point for all our packaging.

In a traditional packaging market, distinction, innovation and sustainability are the key to long-term success.
Pet is the perfect alternative to traditional raw materials such as HDPE and LDPE.

Some advantages of Pet over HDPE and LDPE:
- Pet is stronger
- Pet is 100% recyclable worldwide
- Recycled Pet is food approved
- 25% to 50% raw material savings compared to HDPE and LDPE
- Pet is cheaper
- 100% Pet packaging from recycled material is possible

Our 4 liter and 5 liter Pet Jerry Cans are a good example of the replacement of HDPE Jerry Cans.
With a weight reduction of 30% and the production possibility from recycled raw material, a fantastic result has been achieved.
These Jerry Cans are mostly used for demi water, screen wash, edible oil, natural vinegar and many other products.

After 2 years of development, our 5 Liter AdBlue Pet Jerry Can with a weight reduction of 50% is an unprecedented innovation!

Our production technologies:

Oval pet packaging:

Naamloos

Oval pet packaging have the advantage that they offer a wider label surface for the consumer and require less space for shipping. With our technology, more heat is retained in the parts of the preform to be stretched, so adjusting the wall thickness is much faster than before.

Pet bottles "Off Center":

Naamloos1

Achieving a uniform wall thickness in an off-center product was difficult with earlier pet blowing methods, but is now 100% possible with our latest technology. It also makes weight reduction and therefore material cost reduction possible.

Grip pet packaging:

Naamloos2

These are used for seasonings, oil, food and various other purposes. We can design suitable grips after we have determined the wishes of the customer.

Neck weight saving:

PetInnovators3 1

Our machines can inflate both the neck and the body of the pet packaging. This makes a substantial saving in the weight of the neck possible, of course in such a way that this does not affect closing the cap.

Direct wall thickness system for pet jars:

PetInnovators3 2

Reinforcement ribs to prevent vacuum formation are generally not used in the production of pet jars. If one encounters problems with vacuum formation, one traditionally opts for more material / thicker wall, but this means an increased cost of the pet jar. With our direct wall thickness system we can reduce the weight of the pet jar and prevent vacuum formation. This means a substantial cost saving.

Thick-walled pet packaging:

PetInnovators5 1

Our technology to produce PET packaging with thick walls that feel like glass increases the potential for PET packaging as a real alternative to glass.

Flange neck technology:

PetInnovators5 2

The Flange neck technology eliminates the need for trimming and other secondary production processes and can significantly reduce neck weight. It is suitable for forming medium and wide necks. It is used for medium-sized oil and water containers and for wide-necked containers for liquids and solids.

Thin-walled pet packaging:

PetInnovators7 1

Thin-walled pet packaging is widely used for refilling systems and packaging designed to reduce waste volume.

Long and narrow neck pet bottles:

PetInnovators7 2

We can also produce long necks of a maximum of 100 mm including the thread section.

Ultra narrow neck:

PetInnovators9

This molding technology is most commonly used for eye drop bottles and other small PET packages. The minimum inner diameter can be approximately Φ5 mm. This technology is suitable for containers with a capacity of up to approximately 20 ml.

Champaign bottom:

PetInnovators10

These are usually used for pet packaging in which appearance has the highest priority. It is also possible to apply this technology on stackable PET packaging.


Special pet neck shapes:

PetInnovators11

Our high-quality injection molding technology supports the formation of all complex pet neck shapes.


Pet package with handle:

PetInnovators12

Even in cases where a very precise design of the part where the handle is attached is required, our technology makes stable casting of these pet packs possible through our extensive integrated wall thickness control. In addition to the pet package with separate lever, we can also produce the pet package with an integrated pet lever, which is welded during the production process.


Mini pet packaging:
PetInnovators13

Small pet containers of approximately 5 ml for pharmaceutical products, eye drops, sample names and the like can be poured with greater precision than glass containers. This molding technology also goes one step further and allows the formation of PET packages with an internal neck diameter of only 5 mm, or variable preformed wall thicknesses for ovalising the pet packaging, while at the same time accurately heating the preform for highly accurate blow-out.


Inconspicuous dividing line technologies:
PetInnovators14

Our mold technologies make production possible woth mold dividing lines that are almost unnoticeable. This allows cavities to be increased by placing dividing lines on the front panel, increasing production by 25-100%.


Extremely Stable production of PP containers with a narrow neck:

PetInnovators15
In addition to Pet, we can also process Polypropylene. A common medical application that uses this feature is transfusion bottles. Our shuttle pre-blow system is a blow system that allows you to maintain the preform temperature with the bars, while quickly inflating the bottle, preventing shrinkage. This makes stable blowing of high-quality, high-precision packaging possible.


Drinking bottles:

PetInnovators16

Functional design has the highest priority with water bottles, including aspects such as cap orientation. We can use our extensive experience to meet these needs. Although it depends on the functions required for the water bottle, materials such as PP, Tritan and PET are suitable for blowing water bottles. Tritan and other heat-resistant materials are ideal for water bottles that are washed with hot or boiling water.

Pet packaging produced from 100% recycled Pet flakes:

PetInnovators17

Our machines can use Pet flakes from crushed and washed PET bottles to inject directly for new pet packaging. The mainstream approach to recycling PET requires pellet material, but with our machines, the costs for pelletizing the recycled PET flakes (transportation, energy, payroll, etc.) are now a thing of the past.

Real production from Bottle to Bottle!